Printed DESIGN OF PRINTED: C hen you want to do a project of electronica simpre think give a professional finish, well we refer to printed boards, who has done a form at least with your ... Plumoncito and ....!, rule or whether to make a PCB with a program, but that's all well you design it and everything but when the hour goes wrong or not know how to spend your Bakelite.
Well there are several ways, one is with paper photographic.
in which one must pass design.
There are others who use A4 bond paper, onion paper, paper goose.
There is also another method, similar to the method of estanpado of poles, and another method that is expensive, using the elements to reveal photographs and using transparent paper osea a paper called "movie role."
Well all this will teach a method similar to the first to talk and is using the following materials.
MATERIALS:
- couche paper of 80 grams or 90-gramos.Buneo but the 90 is more commercial.
- A laser printer, preferably HP.
- Your design and echo in some PCB software.
- Adhesive Tape.
- Iron normal home use.
- Your acid for print.
- an empty vessel.
PROCEDURE:
1. Have your design ready, I throw in some PCB software, well I use the Proteus ARES I used to print and also for simulations (Isis).
Proteus v6.7 download
Proteus v6.9 download
There are other programs that generate PCB (printed design) how are you:
- Eagle
-Orcad-TraxMaker
-WinCircuit
-Proteus-Ares
-PCB Wizard, among several others.
2. If you have your laser printer you must first place the rubber sheet 80 or 90 grams in the printer to print in the most shiny, then print your design on the sheet, haslo toner preferably with a strong bone more ink, which he did out perfect and more likely to get it right and vacant ...!
3. Once your design already printed on the sheet couche, it must now verify that your Bakelite is clean of any grease or dirt, if not well pass it a dish washing sponge those with nothing haslo mild detergent without damaging the board.
4. Once obtained clean plate, proceeds to put the sheet with your design couche on your Bakelite, for this cuts the sheet as you design your baqulita but leaving a little edge, "For this ..? .
to Haci is able to hold the paper with the adhesive tape by hand behind the plate.
5. Once done this and grip the paper, bakelite, proceeds to light the grill. Once the iron is hot or so not so, proceed to "Iron your Bakelite with the blade, move the iron is desir on the role that this subject by Bakelite, haslo like ironing a dress, give a little squeezing past the plate on the plate.
not do it too long as the paper burns .. How do I know you are ready ..? Well to pass the iron over the paper subject to the Bakelite notice that the lines of your design track traslucira for the role, you will notice the clues bone are seen sheet. Some lines do not notice much stronger than others but estan.Has this for 1 to 2 minutes.
6. Once already see all the tracks for the role (some more q other), proceeds to remove the plate and see that while cool, lift the paper forming air like balls, this really only occurs in areas that is not your design on the white bone.
After this see if some parts of the track have been raised, this means desir not have stuck it to bakelite, if so pass the plate again for the defective area.
7. After around and being cold plate and proceeds to put the cold water (warm preferncia, goes faster on paper), and proceeds to slowly throw your hand with water on the plate, until you feel it getting wet inside and once this comes to slowly rub with fingertips paper, and notice that it will slowdown the paper carefully haslo but fouled the tracks.
Veras the paper will slowdown and you can only track your design bone
8. A removed all the paper, correcting if you ate there a track with a marker for haslo impresos.Luego this should put your plate to the acid (ferric chloride or ferric chloride Ferric Iron or simply ask as acid to boxes in your nearest electronics store to home) in the container.
Move gently with the acid container and the plate until you feel that because acid has eaten all the copper is only the tracks of your design, preferably put the plate upside down (face design to below).
Once this removes your plate, wash with a little ring tones (those who used to wash the pots) or else pass it draft and removed all the black in your tracks (printer ink) and q really ue charge a seeming echo see this, your plate will be ready .... !
Avail now have a professional design, easy and convenient way ..
NOTE:
plate not much pressure to do this because ink on the printer you spill your design imprimistes and perhaps eventually join with other tracks and will make short, if this happens just with a knife to separate a must see after you've removed the paper with water.
If there are questions or comments hasmela know or if you want some pictures of procedimientode this method, please write a comment on the page or else write to my mail:
mailto: @ axgt8 hotmail.com,
of choice for more often in axgt8@hotmail.com
Links Author:
RoboticaCCencho
